What it means
WLAN error on a Liebherr Touch & Swipe freezer means it could not connect to your WLAN. Check the WLAN connection and connect the freezer again. The guide says the message only shows the first time the appliance is set up.
Liebherr freezer WLAN error / Control board and communication
WLAN error on a Liebherr Touch & Swipe freezer means it could not connect to your WLAN. Check the WLAN connection and connect the freezer again. The guide says the message only shows the first time the appliance is set up.
Also shown as WLAN error
WLAN error on a Liebherr Touch & Swipe freezer means it could not connect to your WLAN. Check the WLAN connection and connect the freezer again. The guide says the message only shows the first time the appliance is set up.
Nothing about this message affects cooling, so no food action is needed.
WLAN error keeps coming back after you reconnect.
Your Liebherr steps, stored on this device alone

Confirm the WLAN at home is working and in range of the freezer.

Follow the guide's WiFi steps to connect the freezer to the WLAN again.

The guide says this message appears only during the first setup. If it shows later, write down when and book a visit.
Give us the model number and what you have already tried, then start your request below.
Book a visitA simplified drawing of a cooling unit; the inside differs between built-in, freestanding and column models. Tap any outlined part to open its photo and the check that belongs to it.

Component reference
Liebherr Touch & Swipe models are run from a touch display.
Read the definitionWLAN error appears if the freezer could not be connected to WLAN. The guide says it shows only the first time the appliance is set up.
Read the supporting manualBegin with the first check: confirm the WLAN at home is working and in range of the freezer.
Read the supporting manualNothing about this message affects cooling, so no food action is needed. Check the freezer temperature as usual.
Read the supporting manualWLAN error is not Connection failure. Connection failure is a Monolith column notice about a disabled connection with a failure number; WLAN error is a network setup message on Touch & Swipe freezers.
Read the supporting manualManufacturer document
Liebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/sfnsth-529i-3033451)
Models: SF 5291, SFNsth 529i
PDF creation date Mon Nov 10 12:53:16 2025 EET; file tag SFNsth529i_237; cover: SF 5291; US product page SFNsth 529i / PDF p. 22, PDF p. 23
Manufacturer document
Liebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/sufnh-365i-3033453)
Models: SUFNc 375i, SUFNd 365i, SUFNh 365i
PDF creation date Mon Sep 7 07:30:39 2026 EEST; file tag SUFNh365i_237; cover: SUFNc 375i, SUFNd 365i; US product page SUFNh 365i / PDF p. 19
Applies to Liebherr Touch & Swipe freezers (SF 5291, SUFNc 375i / SUFNd 365i). Sources: two User Guide files, checked November 2026.
WLAN error appears if the freezer could not be connected to WLAN. The guide says it shows only the first time the appliance is set up.
Confirm the WLAN at home is working and in range of the freezer.
Any of these: WLAN error keeps coming back after you reconnect. It appears long after first setup.
Applies to Liebherr Touch & Swipe freezers (SF 5291, SUFNc 375i / SUFNd 365i).
No. It concerns the network link only.
If it keeps coming back after you reconnect, or appears long after first setup.
Liebherr alarms, symptoms, cooling parts, repair visits
Error on a Liebherr Touch & Swipe freezer means an appliance module reports an error. Touch the display to see the code and write it down. Liebherr's guides do not list what the codes mean, so book a technician with us and give the code.
A Liebherr freezer that runs warm often has a simple cause that the user guide lists: a door left ajar, a blocked ventilation grille, a hot room, a heat source nearby, too much fresh food added without SuperFrost, or a setting that is too warm. Work through that list. If it stays warm, book a technician.
Liebherr Touch & Swipe models are run from a touch display. You tap to confirm, hold for about 3 seconds to switch a function, and swipe to move through menus. After 1 minute untouched it dims to sleep mode, and after 10 seconds it steps back a menu. A warning on it is read by touching the display.
Book a diagnostic for your exact model, carried out beside the unit.
Office details, plus the access notes to pass on to us.