Inside the appliance
IceMaker water inflow setting. In plain English.
Liebherr lets you tune the IceMaker water inflow from 1 (least) to 8 (most), with 4 set at the factory. If the flow does not suit your water pressure or the cube size, change the value in the display once the IceMaker has been started and switched on.

Where it fits.
IceMaker water inflow setting in the appliance
Set in the appliance display; it controls the water valve feeding the IceMaker.
The image shows a typical example of this part. It does not say which replacement fits your model.
What changes when the cooling system needs attention.
IceMaker water inflow setting problems can show up as warmer shelves or an alarm that keeps returning. The part is tested before anyone decides it is the cause.

Liebherr freezer not cold enough
A Liebherr freezer that runs warm often has a simple cause that the user guide lists: a door left ajar, a blocked ventilation grille, a hot room, a heat source nearby, too much fresh food added without SuperFrost, or a setting that is too warm. Work through that list. If it stays warm, book a technician.

Liebherr freezer does not work or will not turn on
If a Liebherr freezer is dead, the user guide lists four things for the owner to rule out first: the freezer was never switched on, the plug is not seated in the wall socket, the fuse behind that socket is not good, or the IEC socket on the back is not plugged in properly. After those, book a technician. Keep the door shut meanwhile.
Owner care, within the model instructions.
Unplug the appliance before any check of your own. Watch for meltwater on the floor and for frost-covered shelves that can stick to skin. Never touch a wet plug, open a cover or go beyond what your model's owner manual allows.
- 1
Start and activate first
The IceMaker must have been started for the first time and be activated before you can set the water inflow.
- 2
Look at the cube size
Liebherr says to adjust the inflow if it does not match the water pressure and the size of the ice cubes.
- 3
Change one step
Pick a value between 1 and 8, for example from 5 to 6, and confirm in the display as the illustration shows.
- 4
Check the water connection
If water is missing altogether, a flashing IceMaker LED or the Check water connection reminder points to the supply.
Cleaning or replacement?
Leave internal testing to a technician.
Ice cubes stay wrong after trying other inflow values.
The display asks you to check the water connection and the line is open.
Arrange a diagnosticSources and model boundaries.
These documents support the IceMaker water inflow setting guidance. Pick the manual that matches your model.
- User Guide, section IceMaker water inflow (CBNsth 779i)
Keep the manual for your exact model handy. See how we research these pages.
What is the factory value?
Liebherr ships the water inflow at 4. Any value from 1 to 8 can be chosen.
What does a higher value do?
Liebherr says 1 is the smallest volume and 8 the largest. Use it to match water pressure and cube size.
When can I change it?
After the IceMaker was started for the first time and is activated.
When do the first cubes arrive?
Liebherr says the IceMaker may need up to a full day to deliver its first cubes.
Liebherr alarms, symptoms, cooling parts, repair visits
From the message to what to do next.
Liebherr IceMaker not making ice cubes
For a Liebherr IceMaker that is not making ice cubes, the user guide lists three causes: the IceMaker is not switched on, its drawer is not closed properly, or the water connection is not open. Fix whichever applies. If the freezer also shows Check water connection, the guide adds a cleaning step. Otherwise, book a technician.
Ice maker repair
Book a diagnostic for your exact model, carried out beside the unit.
Find your metro
Office details, plus the access notes to pass on to us.

