On this page
- Unplug and empty the freezer first; never use steam cleaners, steel wool or abrasive cleaners. 1
- TubeClean takes up to 60 minutes and needs an empty 1.5 l (1.59 qt) vessel, no taller than 10 cm (3 15/16 in), under the IceMaker. 1
- Leave the drawer magnet and the grease on the rails alone. 1
- After cleaning, switch on, start SuperFrost and refill the freezer only when it is cold enough. 1
How do I clean a Liebherr freezer safely?#
Unplug it and empty it first. Then wipe with a soft cloth and lukewarm water, with a pH-neutral all-purpose cleaner if the dirt needs it. Liebherr warns against steel wool, scouring sponges, abrasive or caustic cleaners and steam cleaners. 1
The manual gives two reasons for the preparation. A live appliance is an electric shock risk, and the refrigerant circuit must not be damaged, which is a fire risk. 1 So no scraping at ice and no sharp tools around the evaporator.
Work in the order the manual does: housing, interior, equipment. The housing gets a soft clean cloth, with lukewarm water and a neutral cleaner when it is very dirty, and glass surfaces can take glass cleaner. 1 Plastic and metal surfaces inside get a soft clean cloth, lukewarm water and a little detergent. 1
Does a NoFrost freezer need defrosting?#
No. The NoFrost system defrosts by itself: moisture condenses on the evaporator and is periodically defrosted and evaporated. The SF 5291 says the appliance does not need to be defrosted, though water droplets may collect at its bottom. 1
If you are decommissioning the unit, put a towel in front of it to catch water that may run out. 1 Our NoFrost defrosting entry explains the system, and the noises guide covers the sounds of a defrost cycle.
How do I clean the drawers, shelves and other equipment?#
Wash shelves, the IceTower pull-out board, drawers and the freezer tray with a soft cloth, lukewarm water and a little dish soap. Wipe retracting rails with a damp cloth. Only the ice cube scoop and the FlexCube may go in the dishwasher, up to 60 °C (140 °F). 1
Two warnings in that list matter. Do not remove the magnet on the drawer, because the magnet ensures that the IceMaker functions. And do not wipe the grease off the retracting rails: it is there for lubrication and must not be removed. 1
Take the equipment out the way the manual shows for your pull-out system. Drawers on full-extension telescopic rails can be pulled out completely, a drawer guided on a glass shelf is a partial pull-out, and the bottom drawer sits on a molded rib with no rails. 1 Leave the bottom drawer in the appliance if the manual says so for your model, since removing it affects ventilation. 1
| Part | How to clean it |
|---|---|
| Housing, glass | Soft cloth, lukewarm water, neutral cleaner; glass cleaner on glass |
| Interior plastic and metal | Soft cloth, lukewarm water, a little detergent |
| Shelves, drawers, IceTower board, freezer tray | Soft cloth, lukewarm water, a little dish soap |
| Retracting rails | Damp cloth only; leave the grease |
| Ice cube scoop, FlexCube | Dishwasher up to 60 °C (140 °F) |
| IceMaker drawer | Warm water and a little detergent; keep the magnet |
What is TubeClean and when do I run it?#
TubeClean is the IceMaker's own rinse. It cleans the water lines of the IceMaker, runs for up to 60 minutes and ends by itself. Liebherr recommends it at first start and, on a water-connected unit, whenever the IceMaker has been out of use for longer than 5 days. 1
You need an empty container with a capacity of 1.5 l (1.59 qt) and a height of no more than 10 cm (3 15/16 in), standing in the drawer under the IceMaker. 1 The container catches the rinse water.
- 1
- 2
- 3
- 4
- 5
Between rinses, the manual says to clean the IceMaker by hand when needed: remove the drawer, wash it with warm water and a little detergent, and push it in again. 1
Should I throw away the first ice?#
Yes, on units without a water filter. After cleaning at first start, the SF 5291 says to dispose of any ice cubes produced within 24 hours of the first ice cube production. 1 The Monolith manual says the first three batches must not be consumed or used, at the first start or after a long idle period. 2
This is why a cleaning routine matters before the first start. If the Check water connection reminder shows up later, the manual's advice after checking the tap is to clean the IceMaker, and then it produces cubes again. 1 Our IceMaker guide covers the settings that sit next to it.
What about the dust filter on a Monolith?#
The Monolith freezer manual has a dust filter in the toe kick area. It tells you to clean it at least at the indicated maintenance intervals, using a vacuum cleaner. 2 You reach it by taking off the ventilation grille. 2
When you put the grille back, check there is no gap between the appliance air divider and the door air divider. The manual says a gap appears if the grille is fitted incorrectly. 2 The ventilation grille entry shows the part.
How do I take the drawers and the IceTower board out?#
Each pull-out system comes apart a little differently, so use the pictures for your model. The general order is: pull the drawer out as far as it goes, lift it at the front or on one side, and take it off toward you. 1
For a drawer on telescopic rails, you pull it fully out, lift the left side and slide the left rail in, then lift the right side, slide the right rail in and remove the drawer to the front. If the rails are not fully in afterwards, push them in completely. 1 A top tilting drawer, a bottom drawer and an IceTower board each have their own routine, all printed in the equipment chapter. 1
The IceTower board comes off after you take out its container and the hang-on tray, then slide the board in, lift it at the front left and right, and take it out to the front. If there are ice cubes in the hang-on tray, empty it first. 1 When you put the board back, set it in at an angle behind the front lug and press it down until it clicks into place. 1
Putting things back matters as much as taking them out. Note the manual's request to leave the bottom drawer in the appliance and never to obstruct the vents on the interior rear wall, because insufficient ventilation raises energy consumption and lowers cooling performance. 1
Freezer drawers and glass panels can also be removed for good. Liebherr calls this VarioSpace: with them out, you have room for large items such as poultry, joints of meat, large game and bulky baked goods, which you can freeze whole for later preparation. Respect the load limits printed for the drawers and panels. 1
What do I do after cleaning?#
Wipe the appliance and the equipment dry, plug the appliance in, switch it on and start SuperFrost. Add the food only when the temperature is cold enough. Repeat the cleaning regularly. 1
SuperFrost helps here because the freezer starts from room temperature. Our SuperFrost timing guide shows how it behaves and when it ends. If the freezer still warns about temperature afterwards, see the Temperature alarm page.
When should I book a technician?#
Book one if TubeClean will not run, the water reminder returns right after a clean, or the freezer fails to cool after being switched on again. Cleaning is an owner job, but the water valve and the IceMaker unit are not. 1
Our independent repair company is separate from Liebherr, and a unit within Liebherr's own warranty is repaired through Liebherr. For other units, book a visit from the freezer repair page. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic.
Sources#
- User GuideLiebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/sfnsth-529i-3033451) · PDF created 10.11.2025; file tag SFNsth529i_237; cover: SF 5291; US product page SFNsth 529i · PDF pages 18, 23, 28, 29, 30, 31
- Use and Care Manual FreezerLiebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/efnhi-9971-3033453) · PDF created 07.04.2026; file tag EFNhi9971_237; cover: MF 1851 / MF 1861 / MF 2451 / MF2461 / MF 3051 / MF 3061 / MF 3651 / MF3661, 7085 979-01 · PDF pages 10, 25





