Using your appliance

Ice on schedule three settings, one drawer

On the SF 5291 the IceMaker needs a cleaned unit and an open water connection, then up to 24 hours for the first cubes. MaxIce lifts output from 1.2 kg to 1.6 kg a day for 48 hours, and the water inflow can be set from 1 to 8. [1]

A glass of ice cubes on a counter beside an open freezer drawer filled with ice cubes under an ice maker.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Clean the IceMaker before the first start and expect up to 24 hours before the first cubes. 1
  • MaxIce raises output from 1.2 kg to 1.6 kg of ice in 24 hours on the SF 5291, then switches itself off after 48 hours. 1
  • Water inflow runs from 1 (least) to 8 (most) and leaves the plant at 4; change it if the cubes do not match your water pressure. 1
  • No ice usually means the function is off, the drawer is not pushed in, or the water connection is closed. 1

How do I start the IceMaker for the first time?#

Clean it first, then switch it on. The SF 5291 manual requires the IceMaker to be cleaned before first use, with the water supply connected and the appliance properly plugged in. The first cubes can take up to 24 hours. 1

The cleaning routine is covered in our guide to cleaning the IceMaker with TubeClean. It runs a rinse of about an hour and ends on its own. 1

The water side has its own rules. The safety notes say to connect to a potable water supply only, and not to use old or already premounted water supply lines. 1 The Monolith manual adds that the manufacturer accepts no liability for damage caused by equipment or water lines between the solenoid valve and the water supply. 2

Two further notes from the Monolith manual are worth keeping. The ice maker makes cubes in quantities a household needs, and the first three batches of ice must not be consumed or used, either after the first start or after a long idle period. 2

What does MaxIce do?#

MaxIce raises the amount of ice the IceMaker makes. On the SF 5291 the normal output is 1.2 kg (2.65 lb) of cubes in 24 hours at -18 °C (about 0 °F), and with MaxIce on it is 1.6 kg (3.53 lb). It switches itself off after 48 hours. 1

You can move between the two settings from the menu. If IceMaker is on and you want extra output, switch to MaxIce. If MaxIce is on and you want to return, activate IceMaker again, which turns MaxIce off and leaves the IceMaker running. 1

ApplianceNormal outputWith MaxIceMaxIce ends by itself
SF 5291 freezer1.2 kg (2.65 lb) per 24 hours1.6 kg (3.53 lb) per 24 hoursAfter 48 hours
Monolith MF freezer100 to 120 cubes per 24 hoursAbout 150 cubes per 24 hoursAfter 36 hours

Higher output costs something. While MaxIce is active the appliance works at a higher output, so noise can be louder and energy use goes up. 1 The Monolith manual calls the increase slight. 2

Switching the IceMaker off is gentle: if cubes are being made at that moment, the process is completed and then the IceMaker goes off. 1 PartyMode, which also activates SuperFrost, switches on the IceMaker with MaxIce for up to 24 hours, but only once the IceMaker has been started for the first time. 1 Our guide to SuperFrost timing covers the other half of that party setting.

What is the water inflow setting for?#

It controls how much water the IceMaker takes in for each batch. You can raise or lower it if the cubes do not suit your water pressure or the size you are getting. The SF 5291 leaves the plant at 4, and you can pick any value from 1 (least water) to 8 (most). 1

Change it one step at a time and judge after a day. The setting needs the IceMaker to have been started for the first time and to be active. 1

  1. 1

    Make sure the IceMaker is active#

    The function must be on and the unit must have run through its first start. 1

    A fingertip touches a black glass display above a freezer drawer, a few small lights and dashes glowing on it.
  2. 2

    Open the water inflow setting#

    Follow the key sequence on the manual's illustration; the text does not spell out the screens. 1

  3. 3

    Move the value by one step#

    Choose a value between 1 and 8. The manual's example switches from 5 to 6. 1

  4. 4

    Wait and compare#

    Check the size of the cubes and the amount of water in the drawer a day later before changing again.

    A hand uses a metal scoop to level clear ice cubes in an open freezer drawer.

The Monolith freezers use a differently named setting called water pressure adjustment. If the cubes are too small (the first few batches always are), you choose E4 for smaller cubes or E6 for larger ones, and the manual warns not to raise it by more than one step because the ice cube tray could overflow. Check the cube size over the next days before another step. 2

The matching part is described in our water inflow entry.

Why does the IceMaker make so little ice?#

Check four things in order: the function is switched on, the drawer is closed properly, the water connection is open, and the appliance itself is connected. Those are the four causes the SF 5291 troubleshooting tables give. 1

The manual's wording is plain. If the IceMaker cannot be switched on, the appliance and therefore the IceMaker are not connected. If it is not making cubes, it is not activated, the drawer is not closed properly, or the water connection is not open. 1

Production also depends on how cold the freezer is. The manual says the lower the temperature, the more ice cubes can be made in a certain period. 1 A freezer that is warmer than usual makes less ice, so also read our freezer not cold enough page if the food feels soft.

Then there is the level in the drawer. When a certain level is reached, the IceMaker stops, and it does not fill the drawer to the very top. Distribute the cubes evenly to raise the capacity, and close the drawer, after which production restarts. 1 The Monolith manual asks you to level the cubes at regular intervals and to keep other objects, such as ice cube trays, out of the container. 2

One part must not be touched. The IceMaker drawer has a magnet, and the cleaning notes say not to remove it because the magnet ensures the IceMaker functions. 1 The glass panel above the IceTower also stays in place: the IceMaker is attached to it, and removing it can damage the unit. 1

What do the two IceMaker reminders mean?#

Check water connection appears when the IceMaker is active but is no longer being supplied with water by a permanent connection. Push in the IceMaker drawer appears when the IceMaker is active but the drawer is open. 1

Both are yellow reminders with an alarm tone, and the interior light can pulse. You end them by fixing the cause, or by deactivating the IceMaker. 1 If the water connection has been checked and the IceMaker is active, the manual says to clean the IceMaker, after which it produces cubes again. 1

Our code pages describe each one: Check water connection and Push in the IceMaker drawer. If a Monolith shows an IceMaker failure instead, see the IceMaker failure page.

What should I do before a long absence?#

Switch the IceMaker off and shut the water. The Monolith manual lists the steps: switch off the water supply, wait 24 hours or until the water alarm appears, then disable the ice maker. 2

The SF 5291 decommissioning list also begins with emptying the appliance, deactivating the IceMaker and MaxIce, and switching the freezer off. 1 The full list is in our guide to taking a Liebherr out of service.

For a shorter break, the cleaning notes of the SF 5291 recommend cleaning the IceMaker whenever it has been out of use for longer than 5 days with a water connection. 1

Where does the ice end up on a model with an IceTower?#

On freezers with a pull-out board, the cubes drop into a tall container called the IceTower, and a hang-on tray holds loose ice. The second tall container beside it is meant for tall items such as pizzas or alcoholic drinks. 1

The pull-out board and its containers can be taken out for cleaning, and the containers are shaped so they cannot be swapped by mistake. 1 Empty the hang-on tray first if it holds cubes. Do not take off the glass panel above the IceTower, because the IceMaker is mounted on it. 1

When do the owner checks run out?#

When the three simple checks pass and ice is still missing, or when water appears where it should not. The owner can check the switch, the drawer and the tap. The valve, the water line and the IceMaker unit are for a technician. 12

Our independent repair company is separate from Liebherr, and a unit within Liebherr's own warranty is repaired through Liebherr. For other units, book a visit and have the model name from the appliance information screen ready. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. The IceMaker entry and the freezer repair page describe what we look at.

Sources#

  1. User GuideLiebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/sfnsth-529i-3033451) · PDF created 10.11.2025; file tag SFNsth529i_237; cover: SF 5291; US product page SFNsth 529i · PDF pages 8, 14, 16, 17, 18, 23, 24, 28, 30, 31, 32, 33
  2. Use and Care Manual FreezerLiebherr-Hausgeräte (US market edition; linked from https://www.liebherr.com/en-us/p/efnhi-9971-3033453) · PDF created 07.04.2026; file tag EFNhi9971_237; cover: MF 1851 / MF 1861 / MF 2451 / MF2461 / MF 3051 / MF 3061 / MF 3651 / MF3661, 7085 979-01 · PDF pages 10, 11, 26

Here to help

Good questions.
Clear answers.

Talk to our team
How long until a new Liebherr IceMaker makes ice?

Up to 24 hours after you switch it on for the first time, according to the SF 5291 manual. The Monolith manual says the same and adds that the first three batches of ice must not be consumed or used. [1][2]

Does MaxIce stay on?

No. On the SF 5291 it switches off by itself after 48 hours, and on the Monolith freezers after 36 hours. You can also turn it off earlier. Output is higher while it runs, and the Monolith manual notes slightly higher energy use. [1][2]

Why did the IceMaker stop before the drawer was full?

It is designed to. The manual says that when ice reaches a certain level in the drawer, production stops, and the drawer is not filled to the top. Spreading the cubes evenly leaves room for more. [1][2]

Can I put an ice cube tray in the drawer too?

The Monolith manual says not to. Extra objects such as ice cube trays can disturb the even spread of the cubes. The SF 5291 manual only asks you to spread the cubes evenly to raise the drawer capacity. [1][2]

Does the freezer temperature change how much ice I get?

Yes. The SF 5291 manual says production depends on the freezer temperature and that the lower the temperature, the more ice cubes can be made in a given time. Its published figures are for -18 °C (about 0 °F). [1]

Let’s take care of it.

Food and wine do not wait.
Book the check.