Read the whole display
Give the message text exactly as shown, with its punctuation, and the model.
Model-specific code library
We decode 14 Liebherr refrigerator entries, 1 with a page of its own.
The Air filter LED on a Liebherr HCB 2092G or CBS 2092G lights when the air filter in the toe kick area needs cleaning. It is routine upkeep, not a problem. Clean the filter and the light should go out.
Read the Air filter LED checks18 researched refrigerator codes. What a Liebherr readout means depends on the model, so rely on the manual for yours.
The Air filter LED on a Liebherr HCB 2092G or CBS 2092G lights when the air filter in the toe kick area needs cleaning. It is routine upkeep, not a problem. Clean the filter and the light should go out.
Routine upkeepConnection failure on a Liebherr Monolith MRB refrigerator means a connection is disabled. The guide says there is no need to move items to another appliance. Note the failure number, then arrange a technician visit.
TechnicianDoor alarm on a Liebherr refrigerator means the door stayed open longer than allowed. Close the door. Touch & Swipe models let you set the delay, while Monolith MRB refrigerators and the HCB 2092G alarm after about 180 seconds. Book a visit if it sounds with the door shut.
Check firstError on a Liebherr Touch & Swipe refrigerator means an appliance module reports an error. Touch the display to read the code and write it down. The guides print no code values, so book a technician with us and give the code.
TechnicianF1 on a Liebherr HCB 2092G or CBS 2092G refrigerator-freezer means the appliance has a problem. The guide prints F1 to F5 on one line with no meaning for each number. Note that F1 shows, then book a technician and give us the number.
TechnicianF2 on a Liebherr HCB 2092G or CBS 2092G refrigerator-freezer means the appliance has a problem. The guide prints F1 to F5 on one line with no meaning for each number. Note that F2 shows, then book a technician and give us the number.
TechnicianF3 on a Liebherr HCB 2092G or CBS 2092G refrigerator-freezer means the appliance has a problem. The guide prints F1 to F5 on one line with no meaning for each number. Note that F3 shows, then book a technician and give us the number.
TechnicianF4 on a Liebherr HCB 2092G or CBS 2092G refrigerator-freezer means the appliance has a problem. The guide prints F1 to F5 on one line with no meaning for each number. Note that F4 shows, then book a technician and give us the number.
TechnicianF5 on a Liebherr HCB 2092G or CBS 2092G refrigerator-freezer means the appliance has a problem. The guide prints F1 to F5 on one line with no meaning for each number. Note that F5 shows, then book a technician and give us the number.
TechnicianFailure XX0000 on a Liebherr Monolith MRB refrigerator is the Device failure screen: a failure number appears, and Liebherr's text tells you to pass it to service. The digits are not decoded. Keep the number with the model and arrange a visit.
TechnicianPower failure alarm on a Liebherr Touch & Swipe refrigerator-freezer appears when the freezing temperature rose because of a power outage. The appliance cools back on its own, but you confirm the message to clear it. Check the food; a repeat with steady power needs a technician.
Check, then bookThe Power failure LED on a Liebherr HCB 2092G or CBS 2092G means the freezer temperature rose too high in the last hours or days because of a power failure. The freezer display flashes too. Touch the alarm icon to read the highest temperature, and check the food.
Check, then bookA light flashing every 15 seconds at the rear of a Liebherr with a speed-controlled compressor means the appliance is in operation and everything is fine. A different interval means emergency mode or a defect, which calls for a visit from us.
Check firstReplace FreshAir activated charcoal filter is a yellow reminder on Liebherr Touch & Swipe refrigerators. Liebherr recommends replacing the filter every 6 months. Replace it, and the reminder comes back after 6 months.
Routine upkeepReplace water filter is a reminder on Liebherr refrigerators with a water filter. Liebherr recommends replacing the water filter every 6 months; the reminder then returns after 6 months. It is routine upkeep, not a problem.
Routine upkeepTemperature alarm on a Liebherr refrigerator-freezer means the temperature in the freezer part drifted from its setting. On Touch & Swipe models, the display shows the warmest reading; above -9 °C (16 °F), check the food. Book a technician if the alarm returns after you clear the cause.
Check, then bookTwo dashes in the freezer temperature display of a Liebherr HCB 2092G or CBS 2092G mean the freezer is not yet below freezing. It shows only below-freezing temperatures, so dashes are normal at first start-up and can also appear after a power failure.
Check firstWLAN error on a Liebherr Touch & Swipe refrigerator means the appliance could not be connected to your WLAN. Connect the appliance to the WLAN again. The message concerns the network link only.
Check firstWe read US User Guides for Touch & Swipe refrigerators and French-door models, the Monolith MRB manuals, the HCB 2092G manual and Liebherr's FAQ page. Refrigerator-only models were read for door alarm and WLAN error only. No manual prints the number behind Error.

We decode 14 Liebherr refrigerator entries, 1 with a page of its own.
We read US User Guides for Touch & Swipe refrigerators and French-door models, the Monolith MRB manuals, the HCB 2092G manual and Liebherr's FAQ page. Refrigerator-only models were read for door alarm and WLAN error only. No manual prints the number behind Error.
Give the message text exactly as shown, with its punctuation, and the model.
Check food after a long power outage or a Temperature alarm before you use it.
If a Liebherr refrigerator is not cold enough, the user guides list the same few causes: the door is not closed properly, the room is too warm, the door has been opened too often or too long, the temperature is set too warm, a heat source is close, or too much fresh food went in. Check those first. If it stays warm, book a technician.
When a Liebherr refrigerator does not work or its display is off, the guides list a short set of checks: whether the appliance is turned on, whether the power cord is properly inserted, whether the circuit breaker or fuse is in order, and on Touch & Swipe models whether the IEC socket is plugged in. If those pass, book a technician.
Liebherr's Touch & Swipe refrigerator guide lists bubbling, hissing, humming, sipping from the self-closing door, whirring from the fan, clicking and valve rattle as normal. Vibration and clattering are the two it marks as error noises. Adjust the feet to level the refrigerator, and secure items. If the sound is not listed, book a technician.
Keep the manual for your exact model handy. See how we research these pages.
We read US User Guides for Touch & Swipe refrigerators and French-door models, the Monolith MRB manuals, the HCB 2092G manual and Liebherr's FAQ page. Refrigerator-only models were read for door alarm and WLAN error only. No manual prints the number behind Error.
Photograph the whole refrigerator panel and the rating plate. Add what the cooler was doing and when the message showed, and do not borrow the explanation of a different unit.
A phrase people once searched for is not manufacturer evidence. When our refrigerator manuals leave a message unexplained, we print its name, point you to help and name no cause.
Open the Liebherr manuals in this refrigerator library and match the model on each cover to your rating plate. A different series comes with its own operating manual.